1AC single-phase motors

IP55; 0,37 kW; S1; 930 1/min; 230 V, 50 Hz ±5%; 2,48 A
End of shaft according to DIN/IEC Ø19 x 40 mm Heat class 155(F)
with operating capacitor nominal power at max 40° C and up to 1000 m above NN
dynamically balanced with half paste spring inserted; Vibration level "N"

• Foot mounting: Removable feet (terminal box can be repositioned).

IP55; 0,55 kW; S1; 930 1/min; 230 V, 50 Hz ±5%; 3,47 A
End of shaft according to DIN/IEC Ø19 x 40 mm Heat class 155(F)
with operating capacitor nominal power at max 40° C and up to 1000 m above NN
dynamically balanced with half paste spring inserted; Vibration level "N"

• Foot mounting: Removable feet (terminal box can be repositioned).

IP55; 0,75 kW; S1; 930 1/min; 230 V, 50 Hz ±5%; 4,73 A
End of shaft according to DIN/IEC Ø19 x 40 mm Heat class 155(F)
with operating capacitor nominal power at max 40° C and up to 1000 m above NN
dynamically balanced with half paste spring inserted; Vibration level "N"

• Foot mounting: Removable feet (terminal box can be repositioned).

• IP55
• 0,37 kW
• S1
• 935 1/min
• 230 V, 50 Hz ±5%
• 2,48 A
• End of shaft according to DIN/IEC Ø19 x 40 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 2,20 kW
• S1
• 975 1/min
• 230 V, 50 Hz ±5%
• 12,06 A
• End of shaft according to DIN/IEC Ø28 x 60 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC thermosensor
• terminal box layer at top
• Efficiency class = IE2, efficiency = 81,8 %
• Start capacitor/start capacitor μF 200μF/300V
• Operating capacitor/run capacitor μF 60μF/450V
• Approach to nominal torque / start- to rated torque 1,87
• tilt-to-rated torque / brakedown-to-rated torque 1,80
• Accommodation to rated current 5,40 / startíng- to rated current
• Capacitor circuit start-up relays/starting relays
• shaft seal (DE/NDE) 30x44x7
• Moment of inertia / moment of inertia (kg*m2) 0,019492140
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 0,12 kW
• S1
• 930 1/min
• 230 V, 50 Hz ±5%
• 0,9 A
• End of shaft according to DIN/IEC Ø11 x 23 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 0,18 kW
• S1
• 930 1/min
• 230 V, 50 Hz ±5%
• 1,34 A
• End of shaft according to DIN/IEC Ø14 x 30 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 0,25 kW
• S1
• 930 1/min
• 230 V, 50 Hz ±5%
• 1,86 A
• End of shaft according to DIN/IEC Ø14 x 30 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 0,55 kW
• S1
• 935 1/min
• 230 V, 50 Hz ±5%
• 3,47 A
• End of shaft according to DIN/IEC Ø19 x 40 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 1,10 kW
• S1
• 945 1/min
• 230 V, 50 Hz ±5%
• 6,73 A
• End of shaft according to DIN/IEC Ø24 x 50 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• IP55
• 1,50 kW
• S1
• 960 1/min
• 230 V, 50 Hz ±5%
• 8,73 A
• End of shaft according to DIN/IEC Ø28 x 60 mm Heat class 155(F)
• Temperature protection: incl. 1 x PTC- PTC resistor
• terminal box layer at top
• housing of die cast aluminium
• Motor feet can be screwed on or unscrewed
• AC motors are suitable for both directions of rotation
• with operating capacitor nominal power at max 40° C and up to 1000 m above NN
• dynamically balanced with half paste spring inserted
• Vibration level "N"
• incl. EG installation declaration with disassembly, operation & maintenance instructions
• Due to the start-up and operating capacitor, the 230V motor has a stronger start-up torque.
• The start-up capacitor is switched off by a centrifugal force switch when the speed is reached.
• At low load, the temperature in the engine increases sharply and this can lead to failures.
• Therefore, it is recommended that single-phase motors should not be operated at a load below 25 % of the rated load.

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).

• Foot mounting: Removable feet (terminal box can be repositioned).