AC motors
Items 1 - 50 of 191
inkl. control circuit, CN1 connector, Operating Manual Controller Type Electronic Alarm Type Power Supply Input Voltage single-Phase 100/110/115 VAC±10% Single-Phase200/220/230 VAC±10% Power Supply Input Frequency 50/60 Hz Speed Setting Methods Set the speed in the following way. • Internal setting device • External Speed Potentiometer: Accessories (Sold separately)PAVR-20KZ (20 kΩ, 1/4 W) • External Voltage: 0–5 VDC & –10 VDC switching, 1 mA min. Function Speed Control, Instantaneous Stop, Bi-Direction, Speed Change, Acceleration/Deceleration (0.3-15 seconds: 1000 r/min At no load) Control Power Supply 24 VDC±10%, 100 mA min. Input Signal Photocoupler Input 4.7 kΩ FWD, REV, INT/EXT, ALARM-RESET Output Signal Open-Collector Output 30 VDC max. SPEED-OUT: 10 mA max., ALARM-OUT: 40 mA max. Protective Function When the following protective functions are activated, the motor will come to a coasting stop, and the alarm output will be turned OFF. The LED of the speed controller blinks the number of times in parentheses( ). • Motor Lock (2 Times): When the motor output shaft is restrained for 5 seconds min., or when the tachogenerator wire is disconnected or poorly connected. • Motor Overheat (9 Times): When the motor's built-in thermal protector operates (OPEN). When the motor wire is broken or poorly connected.
• Description of Specification Items
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: cable Type
- Gear Ratio: -
- Time Rating: Continuous
- Voltage/ Frequency/ Current: single-Phase 200 VAC / 50 Hz / 1.6 A
single-Phase 200 VAC / 60 Hz / 1.7 A - Starting Torque (Motor Shaft): single-Phase 200 VAC / 50 Hz: 0.98 N·m
single-Phase 200 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
single-Phase 200 VAC / 60 Hz: 1.27 N·m / 1500 r/min - capacitor: Product name: CH120BFAUL, Capacity: 12 µF, Rated voltage: 450 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 5.0 kg
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: -
- Time Rating: Continuous
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 5.0 kg
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
Out of stock
31.3.2025 Discontinued Product
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: -
- Time Rating: Continuous
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - Overheat Protective Device Type: Thermal protector
- Mass: 5.0 kg
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: -
- Time Rating: Continuous
- Voltage/ Frequency/ Current: Three-Phase380 VAC / 50 Hz / 0.56 A
Three-Phase380 VAC / 60 Hz / 0.54 A
Three-Phase400 VAC / 50 Hz / 0.55 A
Three-Phase400 VAC / 60 Hz / 0.52 A
Three-Phase415 VAC / 50 Hz / 0.54 A - Starting Torque (Motor Shaft): Three-Phase 380 VAC / 50 Hz: 1.47 N·m
Three-Phase 380 VAC / 60 Hz: 1.24 N·m
Three-Phase 400 VAC / 50 Hz: 1.47 N·m
Three-Phase 400 VAC / 60 Hz: 1.24 N·m
Three-Phase 415 VAC / 50 Hz: 1.47 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 380 VAC / 50 Hz: 1.47 N·m / 1300 r/min
Three-Phase 380 VAC / 60 Hz: 1.24 N·m / 1550 r/min
Three-Phase 400 VAC / 50 Hz: 1.47 N·m / 1300 r/min
Three-Phase 400 VAC / 60 Hz: 1.24 N·m / 1550 r/min
Three-Phase 415 VAC / 50 Hz: 1.47 N·m / 1300 r/min - Overheat Protective Device Type: Thermal protector
- Mass: 5.0 kg
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
• It cannot be used in combination with inverter. The insulation of the motor winding may deteriorate and be damaged.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
• It cannot be used in combination with inverter. The insulation of the motor winding may deteriorate and be damaged.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: cable Type
- Gear Ratio: 3.6
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 500 r/min
single-Phase 115 VAC / 60 Hz: 500 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 4.1 N·m
single-Phase 115 VAC / 60 Hz: 4.1 N·m - Permissible Inertia J: 25×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: cable Type
- Gear Ratio: 9
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 200 r/min
single-Phase 115 VAC / 60 Hz: 200 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 10.3 N·m
single-Phase 115 VAC / 60 Hz: 10.3 N·m - Permissible Inertia J: 162×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: cable Type
- Gear Ratio: 3
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 220 VAC / 50 Hz / 1.5 A
single-Phase 220 VAC / 60 Hz / 1.5 A
single-Phase 230 VAC / 50 Hz / 1.5 A
single-Phase 230 VAC / 60 Hz / 1.5 A - Starting Torque (Motor Shaft): single-Phase 220 VAC / 50 Hz: 0.98 N·m
single-Phase 220 VAC / 60 Hz: 0.98 N·m
single-Phase 230 VAC / 50 Hz: 0.98 N·m
single-Phase 230 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 220 VAC / 50 Hz: 1.52 N·m / 1250 r/min
single-Phase 220 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 230 VAC / 50 Hz: 1.52 N·m / 1250 r/min
single-Phase 230 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 220 VAC / 50 Hz: 500 r/min
single-Phase 220 VAC / 60 Hz: 600 r/min
single-Phase 230 VAC / 50 Hz: 500 r/min
single-Phase 230 VAC / 60 Hz: 600 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 220 VAC / 50 Hz: 4.1 N·m
single-Phase 220 VAC / 60 Hz: 3.4 N·m
single-Phase 230 VAC / 50 Hz: 4.1 N·m
single-Phase 230 VAC / 60 Hz: 3.4 N·m - Permissible Inertia J: 18×10-4 kg·m2
- capacitor: Product name: CH100BFAUL, Capacity: 10 µF, Rated voltage: 450 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: cable Type
- Gear Ratio: 18
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 200 VAC / 50 Hz / 1.6 A
single-Phase 200 VAC / 60 Hz / 1.7 A - Starting Torque (Motor Shaft): single-Phase 200 VAC / 50 Hz: 0.98 N·m
single-Phase 200 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
single-Phase 200 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 200 VAC / 50 Hz: 83 r/min
single-Phase 200 VAC / 60 Hz: 100 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 200 VAC / 50 Hz: 23.1 N·m
single-Phase 200 VAC / 60 Hz: 19.7 N·m - Permissible Inertia J: 648×10-4 kg·m2
- capacitor: Product name: CH120BFAUL, Capacity: 12 µF, Rated voltage: 450 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 3
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 600 r/min
single-Phase 115 VAC / 60 Hz: 600 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 3.4 N·m
single-Phase 115 VAC / 60 Hz: 3.4 N·m - Permissible Inertia J: 18×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 3.6
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 500 r/min
single-Phase 115 VAC / 60 Hz: 500 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 4.1 N·m
single-Phase 115 VAC / 60 Hz: 4.1 N·m - Permissible Inertia J: 25×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 5
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 360 r/min
single-Phase 115 VAC / 60 Hz: 360 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 5.7 N·m
single-Phase 115 VAC / 60 Hz: 5.7 N·m - Permissible Inertia J: 50×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 6
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 300 r/min
single-Phase 115 VAC / 60 Hz: 300 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 6.9 N·m
single-Phase 115 VAC / 60 Hz: 6.9 N·m - Permissible Inertia J: 72×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 7.5
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 240 r/min
single-Phase 115 VAC / 60 Hz: 240 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 8.6 N·m
single-Phase 115 VAC / 60 Hz: 8.6 N·m - Permissible Inertia J: 112×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 9
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 200 r/min
single-Phase 115 VAC / 60 Hz: 200 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 10.3 N·m
single-Phase 115 VAC / 60 Hz: 10.3 N·m - Permissible Inertia J: 162×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 3
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 500 r/min
Three-Phase 200 VAC / 60 Hz: 600 r/min
Three-Phase 220 VAC / 60 Hz: 600 r/min
Three-Phase 230 VAC / 60 Hz: 600 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 4 N·m
Three-Phase 200 VAC / 60 Hz: 3.4 N·m
Three-Phase 220 VAC / 60 Hz: 3.3 N·m
Three-Phase 230 VAC / 60 Hz: 3.2 N·m - Permissible Inertia J: 18×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 3.6
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 417 r/min
Three-Phase 200 VAC / 60 Hz: 500 r/min
Three-Phase 220 VAC / 60 Hz: 500 r/min
Three-Phase 230 VAC / 60 Hz: 500 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 4.8 N·m
Three-Phase 200 VAC / 60 Hz: 4.1 N·m
Three-Phase 220 VAC / 60 Hz: 4 N·m
Three-Phase 230 VAC / 60 Hz: 3.8 N·m - Permissible Inertia J: 25×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 5
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 300 r/min
Three-Phase 200 VAC / 60 Hz: 360 r/min
Three-Phase 220 VAC / 60 Hz: 360 r/min
Three-Phase 230 VAC / 60 Hz: 360 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 6.7 N·m
Three-Phase 200 VAC / 60 Hz: 5.6 N·m
Three-Phase 220 VAC / 60 Hz: 5.5 N·m
Three-Phase 230 VAC / 60 Hz: 5.3 N·m - Permissible Inertia J: 50×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 6
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 250 r/min
Three-Phase 200 VAC / 60 Hz: 300 r/min
Three-Phase 220 VAC / 60 Hz: 300 r/min
Three-Phase 230 VAC / 60 Hz: 300 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 8 N·m
Three-Phase 200 VAC / 60 Hz: 6.8 N·m
Three-Phase 220 VAC / 60 Hz: 6.6 N·m
Three-Phase 230 VAC / 60 Hz: 6.4 N·m - Permissible Inertia J: 72×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 7.5
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 200 r/min
Three-Phase 200 VAC / 60 Hz: 240 r/min
Three-Phase 220 VAC / 60 Hz: 240 r/min
Three-Phase 230 VAC / 60 Hz: 240 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 10.1 N·m
Three-Phase 200 VAC / 60 Hz: 8.4 N·m
Three-Phase 220 VAC / 60 Hz: 8.3 N·m
Three-Phase 230 VAC / 60 Hz: 8 N·m - Permissible Inertia J: 112×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 9
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 167 r/min
Three-Phase 200 VAC / 60 Hz: 200 r/min
Three-Phase 220 VAC / 60 Hz: 200 r/min
Three-Phase 230 VAC / 60 Hz: 200 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 12.1 N·m
Three-Phase 200 VAC / 60 Hz: 10.1 N·m
Three-Phase 220 VAC / 60 Hz: 10 N·m
Three-Phase 230 VAC / 60 Hz: 9.6 N·m - Permissible Inertia J: 162×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 12.5
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 144 r/min
single-Phase 115 VAC / 60 Hz: 144 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 13.7 N·m
single-Phase 115 VAC / 60 Hz: 13.7 N·m - Permissible Inertia J: 312×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 15
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 120 r/min
single-Phase 115 VAC / 60 Hz: 120 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 16.4 N·m
single-Phase 115 VAC / 60 Hz: 16.4 N·m - Permissible Inertia J: 450×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 18
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 100 r/min
single-Phase 115 VAC / 60 Hz: 100 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 19.7 N·m
single-Phase 115 VAC / 60 Hz: 19.7 N·m - Permissible Inertia J: 648×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 25
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 72 r/min
single-Phase 115 VAC / 60 Hz: 72 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 27.3 N·m
single-Phase 115 VAC / 60 Hz: 27.3 N·m - Permissible Inertia J: 1250×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 30
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 60 r/min
single-Phase 115 VAC / 60 Hz: 60 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 32.8 N·m
single-Phase 115 VAC / 60 Hz: 32.8 N·m - Permissible Inertia J: 1800×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 36
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 50 r/min
single-Phase 115 VAC / 60 Hz: 50 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 39.3 N·m
single-Phase 115 VAC / 60 Hz: 39.3 N·m - Permissible Inertia J: 2592×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
Out of stock
31.3.2025 Discontinued Product
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 12.5
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 120 r/min
Three-Phase 200 VAC / 60 Hz: 144 r/min
Three-Phase 220 VAC / 60 Hz: 144 r/min
Three-Phase 230 VAC / 60 Hz: 144 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 16 N·m
Three-Phase 200 VAC / 60 Hz: 13.4 N·m
Three-Phase 220 VAC / 60 Hz: 13.2 N·m
Three-Phase 230 VAC / 60 Hz: 12.7 N·m - Permissible Inertia J: 312×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 15
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 100 r/min
Three-Phase 200 VAC / 60 Hz: 120 r/min
Three-Phase 220 VAC / 60 Hz: 120 r/min
Three-Phase 230 VAC / 60 Hz: 120 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 19.2 N·m
Three-Phase 200 VAC / 60 Hz: 16.1 N·m
Three-Phase 220 VAC / 60 Hz: 15.9 N·m
Three-Phase 230 VAC / 60 Hz: 15.2 N·m - Permissible Inertia J: 450×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 18
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 83 r/min
Three-Phase 200 VAC / 60 Hz: 100 r/min
Three-Phase 220 VAC / 60 Hz: 100 r/min
Three-Phase 230 VAC / 60 Hz: 100 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 23.1 N·m
Three-Phase 200 VAC / 60 Hz: 19.4 N·m
Three-Phase 220 VAC / 60 Hz: 19 N·m
Three-Phase 230 VAC / 60 Hz: 18.3 N·m - Permissible Inertia J: 648×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 25
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 60 r/min
Three-Phase 200 VAC / 60 Hz: 72 r/min
Three-Phase 220 VAC / 60 Hz: 72 r/min
Three-Phase 230 VAC / 60 Hz: 72 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 32 N·m
Three-Phase 200 VAC / 60 Hz: 26.9 N·m
Three-Phase 220 VAC / 60 Hz: 26.4 N·m
Three-Phase 230 VAC / 60 Hz: 25.4 N·m - Permissible Inertia J: 1250×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 30
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 50 r/min
Three-Phase 200 VAC / 60 Hz: 60 r/min
Three-Phase 220 VAC / 60 Hz: 60 r/min
Three-Phase 230 VAC / 60 Hz: 60 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 38.4 N·m
Three-Phase 200 VAC / 60 Hz: 32.3 N·m
Three-Phase 220 VAC / 60 Hz: 31.7 N·m
Three-Phase 230 VAC / 60 Hz: 30.4 N·m - Permissible Inertia J: 1800×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 36
- Time Rating: Continuous
- Rotation Direction: opposite direction as the motor shaft
- Voltage/ Frequency/ Current: Three-Phase 200 VAC / 50 Hz / 1.1 A
Three-Phase 200 VAC / 60 Hz / 1.1 A
Three-Phase 220 VAC / 60 Hz / 0.95 A
Three-Phase 230 VAC / 60 Hz / 0.95 A - Starting Torque (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m
Three-Phase 200 VAC / 60 Hz: 1.25 N·m
Three-Phase 220 VAC / 60 Hz: 1.23 N·m
Three-Phase 230 VAC / 60 Hz: 1.18 N·m - Rated torque/ Rated Speed (Motor Shaft): Three-Phase 200 VAC / 50 Hz: 1.49 N·m / 1250 r/min
Three-Phase 200 VAC / 60 Hz: 1.25 N·m / 1500 r/min
Three-Phase 220 VAC / 60 Hz: 1.23 N·m / 1550 r/min
Three-Phase 230 VAC / 60 Hz: 1.18 N·m / 1600 r/min - The Speed When Installing gearhead: Three-Phase 200 VAC / 50 Hz: 42 r/min
Three-Phase 200 VAC / 60 Hz: 50 r/min
Three-Phase 220 VAC / 60 Hz: 50 r/min
Three-Phase 230 VAC / 60 Hz: 50 r/min - Permissible Torque of gearhead Output Shaft: Three-Phase 200 VAC / 50 Hz: 40 N·m
Three-Phase 200 VAC / 60 Hz: 38.7 N·m
Three-Phase 220 VAC / 60 Hz: 38.1 N·m
Three-Phase 230 VAC / 60 Hz: 36.5 N·m - Permissible Inertia J: 2592×10-4 kg·m2
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 100
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 18 r/min
single-Phase 115 VAC / 60 Hz: 18 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 40 N·m
single-Phase 115 VAC / 60 Hz: 40 N·m - Permissible Inertia J: 5000×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 120
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 15 r/min
single-Phase 115 VAC / 60 Hz: 15 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 40 N·m
single-Phase 115 VAC / 60 Hz: 40 N·m - Permissible Inertia J: 5000×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 150
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 12 r/min
single-Phase 115 VAC / 60 Hz: 12 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 40 N·m
single-Phase 115 VAC / 60 Hz: 40 N·m - Permissible Inertia J: 5000×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
- Frame Size: 104 mm
- Output Power: 200 W
- series: BH series
- Type: With Terminal Box
- Gear Ratio: 180
- Time Rating: Continuous
- Rotation Direction: same direction as the motor shaft
- Voltage/ Frequency/ Current: single-Phase 110 VAC / 60 Hz / 3 A
single-Phase 115 VAC / 60 Hz / 3 A - Starting Torque (Motor Shaft): single-Phase 110 VAC / 60 Hz: 0.88 N·m
single-Phase 115 VAC / 60 Hz: 0.98 N·m - Rated torque/ Rated Speed (Motor Shaft): single-Phase 110 VAC / 60 Hz: 1.27 N·m / 1500 r/min
single-Phase 115 VAC / 60 Hz: 1.27 N·m / 1500 r/min - The Speed When Installing gearhead: single-Phase 110 VAC / 60 Hz: 10 r/min
single-Phase 115 VAC / 60 Hz: 10 r/min - Permissible Torque of gearhead Output Shaft: single-Phase 110 VAC / 60 Hz: 40 N·m
single-Phase 115 VAC / 60 Hz: 40 N·m - Permissible Inertia J: 5000×10-4 kg·m2
- capacitor: Product name: CH400CFAUL2, Capacity: 40 µF, Rated voltage: 250 VAC
- Overheat Protective Device Type: Thermal protector
- Mass: 8.0 kg (With gearhead)
• The speed when the gearhead is installed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 to 20% less, depending on the load.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
[Note]
• If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. Be sure to turn the power supply off before inspecting.
Items 1 - 50 of 191