Self-priming pumps

This category includes Calpeda self-priming pumps for water supply, well water extraction, pressure boosting, irrigation, drainage and a wide range of domestic, commercial and industrial applications.

The range covers different pump technologies – from self-priming jet pumps and liquid ring pumps to centrifugal pumps with open impellers and horizontal multistage self-priming centrifugal pumps. This allows different requirements for flow rate, head, pumped liquid, materials and supply voltage to be matched to the application.

Self-priming pumps for wells, water supply and pressure boosting
Jet pumps with built-in ejector
Multistage self-priming centrifugal pumps for higher delivery heads
Liquid ring pumps for applications involving air or gas in the pumped liquid
Open-impeller centrifugal pumps for clean or slightly dirty water
Cast-iron, bronze and stainless-steel versions
Single-phase and three-phase motor versions available

This category includes the Calpeda A, CA, MXA, NG, NGL and NGX series. When selecting the appropriate pump, the required flow rate, delivery head, suction lift, pumped liquid, material, connection size and supply voltage should be considered.

MXA 203 horizontal multi-stage self-priming centrifugal pump

Construction: Horizontal, multi-stage, self-priming centrifugal pump of block construction; One-piece shell of stainless steel with chromium-nickel and steps of noryl
Design: Stainless steel design with jacket housing of AISI 304
Applications: For water supply, home and garden applications and watering
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,37 kW / 0,5 HP
Rated current: 2,4 A at 230 V / 1,4 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 4 m3/h
Maximum pump head according to the characteristic curve: 32 m
Characteristic curve Q/H: 0 m3/h → 32 m; 1 m3/h → 28 m; 2 m3/h → 24 m; 3 m3/h → 19 m; 4 m3/h → 14 m
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Suction height: to 8 m
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 115 mm; b 30 mm; fM 362 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 176 mm; l5 161 mm; m1 33 mm; m3 8 mm; n1 146 mm; n2 112 mm; s 9 mm; w 102 mm; w1 102 mm
Article weight: 6,8 kg
Materials: pump housing and housing cover AISI 304; shaft AISI 430F; suction and stepped housings and impeller Noryl PPO-GF20; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55

SKU:: 662A0031000
Shipping weight:: 8.84 kg
Item weight:: 6.80 kg

408,38 € *

Available

Delivery time: ca. 3 weeks

NGX 3/100 self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,65 kW / 0,9 HP
Rated current: 3 A at 230 V / 1,7 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 3,6 m3/h
Maximum pump head according to the characteristic curve: 50 m
Characteristic curve Q/H: 0 m3/h → 50 m; 0,3 m3/h → 45,9 m; 0,5 m3/h → 44 m; 1 m3/h → 39,4 m; 2 m3/h → 31,3 m; 2,4 m3/h → 28,5 m; 3 m3/h → 24,8 m; 3,2 m3/h → 23,7 m; 3,6 m3/h → 21,7 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 115 mm; b 30 mm; fM 391 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 192 mm; l5 161.00 mm; m1 33 mm; m2 25 mm; m3 8 mm; n1 146 mm; n2 112 mm; s 9 mm; w 95 mm; w1 112 mm
Article weight: 8,3 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 72A51030000
Shipping weight:: 10.79 kg
Item weight:: 8.30 kg

271,61 € *

Available

Delivery time: ca. 3 weeks

MXA 403/A horizontal multi-stage self-priming centrifugal pump

Construction: Horizontal, multi-stage, self-priming centrifugal pump of block construction; One-piece shell of stainless steel with chromium-nickel and steps of noryl
Design: Stainless steel design with jacket housing of AISI 304
Applications: For water supply, home and garden applications and watering
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,55 kW / 0,75 HP
Rated current: 2,8 A at 230 V / 1,6 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 6,5 m3/h
Maximum pump head according to the characteristic curve: 34 m
Characteristic curve Q/H: 0 m3/h → 34 m; 2 m3/h → 30 m; 3 m3/h → 28 m; 4 m3/h → 25 m; 5 m3/h → 22 m; 6 m3/h → 17 m; 6,5 m3/h → 15 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Suction height: to 8 m
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 115 mm; b 30 mm; fM 391 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 192 mm; l5 161 mm; m1 33 mm; m3 8 mm; n1 146 mm; n2 112 mm; s 9 mm; w 112 mm; w1 112 mm
Article weight: 8,8 kg
Materials: pump housing and housing cover AISI 304; shaft AISI 430F; suction and stepped housings and impeller Noryl PPO-GF20; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55
Revision: A

SKU:: 662A1031000
Shipping weight:: 11.44 kg
Item weight:: 8.80 kg

465,80 € *

Available

Delivery time: ca. 3 weeks

MXA 204/A horizontal multi-stage self-priming centrifugal pump

Construction: Horizontal, multi-stage, self-priming centrifugal pump of block construction; One-piece shell of stainless steel with chromium-nickel and steps of noryl
Design: Stainless steel design with jacket housing of AISI 304
Applications: For water supply, home and garden applications and watering
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,55 kW / 0,75 HP
Rated current: 2,8 A at 230 V / 1,6 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 4,5 m3/h
Maximum pump head according to the characteristic curve: 45 m
Characteristic curve Q/H: 0 m3/h → 45 m; 1 m3/h → 40 m; 2 m3/h → 34 m; 3 m3/h → 27 m; 4 m3/h → 20 m; 4,5 m3/h → 15 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Suction height: to 8 m
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 115 mm; b 30 mm; fM 691 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 192 mm; l5 161 mm; m1 33 mm; m3 8 mm; n1 146 mm; n2 112 mm; s 9 mm; w 112 mm; w1 112 mm
Article weight: 8,9 kg
Materials: pump housing and housing cover AISI 304; shaft AISI 430F; suction and stepped housings and impeller Noryl PPO-GF20; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55
Revision: A

SKU:: 662A0041000
Shipping weight:: 11.57 kg
Item weight:: 8.90 kg

449,44 € *

Available

Delivery time: ca. 3 weeks

MXA 404/B horizontal multi-stage self-priming centrifugal pump

Construction: Horizontal, multi-stage, self-priming centrifugal pump of block construction; One-piece shell of stainless steel with chromium-nickel and steps of noryl
Design: Stainless steel design with jacket housing of AISI 304
Applications: For water supply, home and garden applications and watering
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,5 A at 230 V / 2 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 7 m3/h
Maximum pump head according to the characteristic curve: 45 m
Characteristic curve Q/H: 0 m3/h → 45 m; 2 m3/h → 40 m; 3 m3/h → 37 m; 4 m3/h → 33 m; 5 m3/h → 28 m; 6 m3/h → 22 m; 6,5 m3/h → 19 m; 7 m3/h → 15 m
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Suction height: to 8 m
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 115 mm; b 30 mm; fM 391 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 192 mm; l5 161 mm; m1 33 mm; m3 8 mm; n1 146 mm; n2 112 mm; s 9 mm; w 112 mm; w1 112 mm
Article weight: 10,8 kg
Materials: pump housing and housing cover AISI 304; shaft AISI 430F; suction and stepped housings and impeller Noryl PPO-GF20; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55
Revision: BB

SKU:: 662A1041100
Shipping weight:: 14.04 kg
Item weight:: 10.80 kg

515,13 € *

Available

Delivery time: ca. 3 weeks

NGX 4/110 self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,7 A at 230 V / 2,2 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 4,5 m3/h
Maximum pump head according to the characteristic curve: 41,6 m
Characteristic curve Q/H: 0 m3/h → 41,6 m; 0,3 m3/h → 40 m; 0,5 m3/h → 39 m; 1 m3/h → 36,6 m; 2 m3/h → 31,9 m; 2,4 m3/h → 30 m; 3 m3/h → 27,3 m; 3,2 m3/h → 26,4 m; 3,6 m3/h → 24,6 m; 4 m3/h → 23 m; 4,5 m3/h → 21,1 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 115 mm; b 30 mm; fM 391 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 192 mm; l5 161.00 mm; m1 33 mm; m2 25 mm; m3 8 mm; n1 146 mm; n2 112 mm; s 9 mm; w 95 mm; w1 112 mm
Article weight: 10,9 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 72A51040000
Shipping weight:: 14.17 kg
Item weight:: 10.90 kg

289,54 € *

Available

Delivery time: ca. 3 weeks

NGL 3/100 compact self-priming jet pump

Construction: Compact self-priming flat well jet pump in block construction with built-in ejector
Design: Embodiment with pump housing made of GJL 200 and housing cover made of AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,65 kW / 0,9 HP
Rated current: 3 A at 230 V / 1,7 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 3,6 m3/h
Maximum pump head according to the characteristic curve: 50 m
Characteristic curve Q/H: 0 m3/h → 50 m; 0,3 m3/h → 45,9 m; 1 m3/h → 39,4 m; 2 m3/h → 31,3 m; 2,4 m3/h → 28,5 m; 3 m3/h → 24,8 m; 3,2 m3/h → 23,7 m; 3,6 m3/h → 21,7 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 113 mm; b 30 mm; fM 388 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 193 mm; l5 161.00 mm; m1 33 mm; m2 25 mm; m3 8 mm; n1 146 mm; n2 113 mm; s 9 mm; w 95 mm; w1 119 mm
Article weight: 11,1 kg
Materials: pump housing GJL 200; housing cover AISI 304; impeller, diffuser and ejector Noryl PPO-GF20; shaft AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 70A51030000
Shipping weight:: 14.43 kg
Item weight:: 11.10 kg

251,17 € *

Available

Delivery time: ca. 3 weeks

MXA 205/B horizontal multi-stage self-priming centrifugal pump

Construction: Horizontal, multi-stage, self-priming centrifugal pump of block construction; One-piece shell of stainless steel with chromium-nickel and steps of noryl
Design: Stainless steel design with jacket housing of AISI 304
Applications: For water supply, home and garden applications and watering
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,7 A at 230 V / 2,2 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 5 m3/h
Maximum pump head according to the characteristic curve: 55,5 m
Characteristic curve Q/H: 0 m3/h → 55,5 m; 1 m3/h → 50 m; 2 m3/h → 43 m; 3 m3/h → 35,5 m; 4 m3/h → 26,6 m; 4,5 m3/h → 21,4 m; 5 m3/h → 15,5 m
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Suction height: to 8 m
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1 1/4; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 462 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 225 mm; l5 213.5 mm; m1 37.5 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 147 mm; w1 147 mm
Article weight: 12,8 kg
Materials: pump housing and housing cover AISI 304; shaft AISI 430F; suction and stepped housings and impeller Noryl PPO-GF20; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55
Revision: BB

SKU:: 662A0051200
Shipping weight:: 16.64 kg
Item weight:: 12.80 kg

669,29 € *

Available

Delivery time: ca. 3 weeks

NGL 4/110 compact self-priming jet pump

Construction: Compact self-priming flat well jet pump in block construction with built-in ejector
Design: Embodiment with pump housing made of GJL 200 and housing cover made of AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,7 A at 230 V / 2,2 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 4,5 m3/h
Maximum pump head according to the characteristic curve: 41,6 m
Characteristic curve Q/H: 0 m3/h → 41,6 m; 0,3 m3/h → 40 m; 1 m3/h → 36,6 m; 2 m3/h → 31,9 m; 2,4 m3/h → 30 m; 3 m3/h → 27,3 m; 3,2 m3/h → 26,4 m; 3,6 m3/h → 24,6 m; 4 m3/h → 23 m; 4,5 m3/h → 21,1 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 113 mm; b 30 mm; fM 388 mm; g1 10 mm; h1 116 mm; h2 61 mm; HD 193 mm; l5 161.00 mm; m1 33 mm; m2 25 mm; m3 8 mm; n1 146 mm; n2 113 mm; s 9 mm; w 95 mm; w1 119 mm
Article weight: 13 kg
Materials: pump housing GJL 200; housing cover AISI 304; impeller, diffuser and ejector Noryl PPO-GF20; shaft AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 70A51040000
Shipping weight:: 16.90 kg
Item weight:: 13.00 kg

269,09 € *

Available

Delivery time: ca. 3 weeks

MXA 405/A horizontal multi-stage self-priming centrifugal pump

Construction: Horizontal, multi-stage, self-priming centrifugal pump of block construction; One-piece shell of stainless steel with chromium-nickel and steps of noryl
Design: Stainless steel design with jacket housing of AISI 304
Applications: For water supply, home and garden applications and watering
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,5 A at 230 V / 2,6 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 8 m3/h
Maximum pump head according to the characteristic curve: 56 m
Characteristic curve Q/H: 0 m3/h → 56 m; 2 m3/h → 51 m; 3 m3/h → 47,5 m; 4 m3/h → 42,5 m; 5 m3/h → 36,5 m; 6 m3/h → 30 m; 6,5 m3/h → 26,5 m; 7 m3/h → 23 m; 8 m3/h → 14 m
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Suction height: to 8 m
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 462 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 225 mm; l5 213.5 mm; m1 37.5 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 147 mm; w1 147 mm
Article weight: 14,5 kg
Materials: pump housing and housing cover AISI 304; shaft AISI 430F; suction and stepped housings and impeller Noryl PPO-GF20; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55
Revision: A

SKU:: 662A1051100
Shipping weight:: 18.85 kg
Item weight:: 14.50 kg

691,91 € *

Available

Delivery time: ca. 3 weeks

NGX 4/16 self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,5 A at 230 V / 2,6 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 4,5 m3/h
Maximum pump head according to the characteristic curve: 57,5 m
Characteristic curve Q/H: 0 m3/h → 57,5 m; 0,3 m3/h → 54 m; 0,5 m3/h → 52 m; 1 m3/h → 47,3 m; 2 m3/h → 40 m; 2,4 m3/h → 37,5 m; 3 m3/h → 34 m; 3,2 m3/h → 32,9 m; 3,6 m3/h → 30,7 m; 4 m3/h → 28,5 m; 4,5 m3/h → 26 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1 1/4; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 462 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 225 mm; l5 213.5 mm; m1 37.5 mm; m2 28 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 113 mm; w1 147 mm
Article weight: 14,8 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 72A50370000
Shipping weight:: 19.24 kg
Item weight:: 14.80 kg

601,61 € *

Available

Delivery time: ca. 3 weeks

NGX 4/18 self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,5 A at 230 V / 2,6 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 5 m3/h
Maximum pump head according to the characteristic curve: 48 m
Characteristic curve Q/H: 0 m3/h → 48 m; 0,3 m3/h → 46 m; 0,5 m3/h → 45 m; 1 m3/h → 42,5 m; 2 m3/h → 37 m; 2,4 m3/h → 35 m; 3 m3/h → 32,5 m; 3,2 m3/h → 31,7 m; 3,6 m3/h → 30,1 m; 4 m3/h → 28,5 m; 4,5 m3/h → 27 m; 5 m3/h → 25 m
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1 1/4; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 488.5 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 225 mm; l5 213.5 mm; m1 37.5 mm; m2 28 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 113 mm; w1 147 mm
Article weight: 14,8 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 72A50371000
Shipping weight:: 19.24 kg
Item weight:: 14.80 kg

601,61 € *

Available

Delivery time: ca. 3 weeks

NGX 4/22 self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,5 A at 230 V / 2,6 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 8,4 m3/h
Maximum pump head according to the characteristic curve: 35,5 m
Characteristic curve Q/H: 0 m3/h → 35,5 m; 0,3 m3/h → 34,8 m; 0,5 m3/h → 34,3 m; 1 m3/h → 33 m; 2 m3/h → 30,5 m; 2,4 m3/h → 29,5 m; 3 m3/h → 28 m; 3,2 m3/h → 27,5 m; 3,6 m3/h → 26,4 m; 4 m3/h → 25,3 m; 4,5 m3/h → 24 m; 5 m3/h → 23 m; 5,5 m3/h → 22 m; 6 m3/h → 21 m; 6,5 m3/h → 20,3 m; 7 m3/h → 19,5 m; 8 m3/h → 18 m; 8,4 m3/h → 17,5 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1 1/4; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 488.5 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 225 mm; l5 213.5 mm; m1 37.5 mm; m2 28 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 113 mm; w1 147 mm
Article weight: 14,8 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner

SKU:: 72A50372000
Shipping weight:: 19.24 kg
Item weight:: 14.80 kg

601,61 € *

Available

Delivery time: ca. 3 weeks

NG 3/A self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,55 kW / 0,75 HP
Rated current: 3 A at 230 V / 1,7 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 3 m3/h
Maximum pump head according to the characteristic curve: 52,1 m
Characteristic curve Q/H: 0 m3/h → 52,1 m; 0,25 m3/h → 49 m; 0,5 m3/h → 45,5 m; 1 m3/h → 40 m; 1,5 m3/h → 36 m; 2 m3/h → 32 m; 2,5 m3/h → 28 m; 3 m3/h → 24 m
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 127 mm; a1 8 mm; b 35 mm; fM 430 mm; g1 11 mm; h1 150 mm; h2 43 mm; HD 207 mm; m1 60 mm; m3 8 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 100 mm
Article weight: 17,3 kg
Materials: pump housing, cover and diffuser plate GJL 200; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: A

SKU:: 70A40031000
Shipping weight:: 22.49 kg
Item weight:: 17.30 kg

439,96 € *

Available

Delivery time: ca. 3 weeks

NGX 6/22/A self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,5 kW / 2 HP
Rated current: 7,5 A at 230 V / 4,3 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 8,4 m3/h
Maximum pump head according to the characteristic curve: 46,5 m
Characteristic curve Q/H: 0 m3/h → 46,5 m; 0,5 m3/h → 45 m; 1 m3/h → 43,5 m; 2 m3/h → 40,5 m; 2,4 m3/h → 39,3 m; 3 m3/h → 37,5 m; 3,2 m3/h → 37 m; 3,6 m3/h → 36 m; 4 m3/h → 35 m; 4,5 m3/h → 33,5 m; 5 m3/h → 32,5 m; 5,5 m3/h → 31,2 m; 6 m3/h → 30 m; 6,5 m3/h → 28,5 m; 7 m3/h → 27,5 m; 8 m3/h → 25,5 m; 8,4 m3/h → 24,5 m3/h
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1 1/4; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 488.5 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 240 mm; l5 213.5 mm; m1 37.5 mm; m2 28 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 113 mm; w1 157.5 mm
Article weight: 17,3 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner
Revision: A

SKU:: 72A50045200
Shipping weight:: 22.49 kg
Item weight:: 17.30 kg

765,60 € *

Available

Delivery time: ca. 3 weeks

NGX 6/18/A self-priming stainless steel jet pump

Construction: High quality self-priming, ingot type, ingot type, with built-in ejector and pump housing of stainless steel
Design: Stainless steel design with pump housing and housing cover from AISI 304
Applications: For well extraction, extraction of water with air or gas content, pressure increase, domestic water supply, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,5 kW / 2 HP
Rated current: 7,5 A at 230 V / 4,3 A at 400 V
Rated speed: 2800 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 6 m3/h
Maximum pump head according to the characteristic curve: 58 m
Characteristic curve Q/H: 0 m3/h → 58 m; 0,5 m3/h → 54,7 m; 1 m3/h → 51,5 m; 2 m3/h → 46 m; 2,4 m3/h → 44 m; 3 m3/h → 41,3 m; 3,2 m3/h → 40,4 m; 3,6 m3/h → 38,7 m; 4 m3/h → 37 m; 4,5 m3/h → 34,7 m; 5 m3/h → 32,5 m; 5,5 m3/h → 30,5 m; 6 m3/h → 28,5 m
Media temperature: 0 to +35 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 8 bar
Connections according to ISO 228: suction side DN1 G 1 1/4; Pressure side DN2 G 1
Dimensions: a 140 mm; b 33 mm; fM 488.5 mm; g1 11 mm; h1 152 mm; h2 68 mm; HD 240 mm; l5 213.5 mm; m1 37.5 mm; m2 28 mm; m3 9.5 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 113 mm; w1 157.5 mm
Article weight: 18,1 kg
Materials: pump housing and housing cover AISI 304; wheel brass CW617N, at NGX 2/80, 3/100 and 4/110 Noryl PPO-GF20; Diffuser and ejector Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; Brass runner
Revision: A

SKU:: 72A50044200
Shipping weight:: 23.53 kg
Item weight:: 18.10 kg

765,60 € *

Available

Delivery time: ca. 3 weeks

NG 4/B self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,7 A at 230 V / 2,2 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 4 m3/h
Maximum pump head according to the characteristic curve: 45,8 m
Characteristic curve Q/H: 0 m3/h → 45,8 m; 0,25 m3/h → 41 m; 0,5 m3/h → 39 m; 1 m3/h → 36 m; 1,5 m3/h → 33 m; 2 m3/h → 31 m; 2,5 m3/h → 29 m; 3 m3/h → 26 m; 3,5 m3/h → 24 m; 4 m3/h → 21 m
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 127 mm; a1 8 mm; b 35 mm; fM 430 mm; g1 11 mm; h1 150 mm; h2 43 mm; HD 207 mm; m1 60 mm; m3 8 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 100 mm
Article weight: 19,3 kg
Materials: pump housing, cover and diffuser plate GJL 200; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: BB

SKU:: 70A40042000
Shipping weight:: 25.09 kg
Item weight:: 19.30 kg

484,42 € *

Available

Delivery time: ca. 3 weeks

A 40-110B/A self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,55 kW / 0,75 HP
Rated current: 2,8 A at 230 V / 1,6 A at 400 V
Rated speed: 2900 min-1
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 18 m3/h
Maximum pump head according to the characteristic curve: 14,4 m
Characteristic curve Q/H: 0 m3/h → 14,4 m; 3,6 m3/h → 12,9 m; 4,8 m3/h → 12,4 m; 6 m3/h → 11,8 m; 7,5 m3/h → 11 m; 8,4 m3/h → 10,4 m; 9,6 m3/h → 9,8 m; 10,8 m3/h → 9 m; 12 m3/h → 8,3 m; 15 m3/h → 6 m; 18 m3/h → 3,4 m3/h
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1 1/2
Dimensions: a 132 mm; b 50 mm; fM 393 mm; g1 12 mm; h1 208 mm; h2 67 mm; HD 206 mm; l1 83 mm; l2 89 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; s 16 mm; w 199 mm
Article weight: 19,5 kg
Materials: pump housing, suction housing and impeller GJL 200; shaft depending on the size AISI 303 or AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier
Revision: A

SKU:: 60F00341000
Shipping weight:: 25.35 kg
Item weight:: 19.50 kg

770,65 € *

Available

Delivery time: ca. 3 weeks

BNG 3/A self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Bronze version with pump housing and bronze lantern CC480K
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,55 kW / 0,75 HP
Rated current: 3 A at 230 V / 1,7 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE2
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 3 m3/h
Maximum pump head according to the characteristic curve: 52,1 m
Characteristic curve Q/H: 0 m3/h → 52,1 m; 0,25 m3/h → 49 m; 0,5 m3/h → 45,5 m; 1 m3/h → 40 m; 1,5 m3/h → 36 m; 2 m3/h → 32 m; 2,5 m3/h → 28 m; 3 m3/h → 24 m
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1; Pressure side DN2 G 1
Dimensions: a 127 mm; a1 8 mm; b 35 mm; fM 430 mm; g1 11 mm; h1 150 mm; h2 43 mm; HD 207 mm; m1 60 mm; m3 8 mm; n1 185 mm; n2 155 mm; s 9.5 mm; w 100 mm
Article weight: 20,6 kg
Materials: Pump housing, cover and diffuser plate bronze CC480K; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 316; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: A

SKU:: 71A40030000
Shipping weight:: 26.78 kg
Item weight:: 20.60 kg

1.517,63 € *

Available

Delivery time: ca. 3 weeks

A 40-110A/B self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,7 A at 230 V / 2,2 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 18 m3/h
Maximum pump head according to the characteristic curve: 17,2 m
Characteristic curve Q/H: 0 m3/h → 17,2 m; 3,6 m3/h → 15,4 m; 4,8 m3/h → 14,9 m; 6 m3/h → 14,2 m; 7,5 m3/h → 13,3 m; 8,4 m3/h → 12,9 m; 9,6 m3/h → 12,1 m; 10,8 m3/h → 11,3 m; 12 m3/h → 10,5 m; 15 m3/h → 8,4 m; 18 m3/h → 5,6 m3/h
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1 1/2
Dimensions: a 132 mm; b 50 mm; fM 393 mm; g1 12 mm; h1 208 mm; h2 67 mm; HD 206 mm; l1 83 mm; l2 89 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; s 16 mm; w 199 mm
Article weight: 20,7 kg
Materials: pump housing, suction housing and impeller GJL 200; shaft depending on the size AISI 303 or AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier
Revision: BB

SKU:: 60F00382000
Shipping weight:: 26.91 kg
Item weight:: 20.70 kg

841,20 € *

Available

Delivery time: ca. 3 weeks

BA 40-110B/A self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Bronze version with pump housing and bronze lantern CC480K
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,55 kW / 0,75 HP
Rated current: 2,8 A at 230 V / 1,6 A at 400 V
Rated speed: 2900 min-1
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 18 m3/h
Maximum pump head according to the characteristic curve: 14,4 m
Characteristic curve Q/H: 0 m3/h → 14,4 m; 3,6 m3/h → 12,9 m; 4,8 m3/h → 12,4 m; 6 m3/h → 11,8 m; 7,5 m3/h → 11 m; 8,4 m3/h → 10,4 m; 9,6 m3/h → 9,8 m; 10,8 m3/h → 9 m; 12 m3/h → 8,3 m; 15 m3/h → 6 m; 18 m3/h → 3,4 m3/h
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1 1/2
Dimensions: a 132 mm; b 50 mm; fM 393 mm; g1 12 mm; h1 208 mm; h2 67 mm; HD 206 mm; l1 83 mm; l2 89 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; s 16 mm; w 199 mm
Article weight: 21,6 kg
Materials: pump housing, suction housing and impeller bronze CC480K; shaft AISI 316; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier
Revision: A

SKU:: 61F00341000
Shipping weight:: 28.08 kg
Item weight:: 21.60 kg

2.088,87 € *

Available

Delivery time: ca. 3 weeks

BA 40-110A/B self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Bronze version with pump housing and bronze lantern CC480K
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 3,7 A at 230 V / 2,2 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 18 m3/h
Maximum pump head according to the characteristic curve: 17,2 m
Characteristic curve Q/H: 0 m3/h → 17,2 m; 3,6 m3/h → 15,4 m; 4,8 m3/h → 14,9 m; 6 m3/h → 14,2 m; 7,5 m3/h → 13,3 m; 8,4 m3/h → 12,9 m; 9,6 m3/h → 12,1 m; 10,8 m3/h → 11,3 m; 12 m3/h → 10,5 m; 15 m3/h → 8,4 m; 18 m3/h → 5,6 m3/h
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1 1/2
Dimensions: a 132 mm; b 50 mm; fM 393 mm; g1 12 mm; h1 208 mm; h2 67 mm; HD 206 mm; l1 83 mm; l2 89 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; s 16 mm; w 199 mm
Article weight: 23,3 kg
Materials: pump housing, suction housing and impeller bronze CC480K; shaft AISI 316; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier
Revision: BB

SKU:: 61F00382000
Shipping weight:: 30.29 kg
Item weight:: 23.30 kg

2.160,73 € *

Available

Delivery time: ca. 3 weeks

A 50-125CE self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 4 A at 230 V / 2,3 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 27 m3/h
Maximum pump head according to the characteristic curve: 13,7 m
Characteristic curve Q/H: 0 m3/h → 13,7 m; 6 m3/h → 12,8 m; 9 m3/h → 12,2 m; 12 m3/h → 11,3 m; 15 m3/h → 10 m; 18 m3/h → 8,5 m; 21 m3/h → 7 m; 24 m3/h → 5,3 m; 27 m3/h → 3,3 m3/h
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 2; Pressure side DN2 G 2
Dimensions: a 147 mm; b 50 mm; fM 490 mm; g1 12 mm; h1 231 mm; h2 64 mm; HD 223 mm; l1 96 mm; l2 102 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; n3 30 mm; s 16 mm; w 263 mm
Article weight: 26,2 kg
Materials: pump housing, suction housing and impeller GJL 200; shaft depending on the size AISI 303 or AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier

SKU:: 60F00821000
Shipping weight:: 34.06 kg
Item weight:: 26.20 kg

1.067,06 € *

Available

Delivery time: ca. 3 weeks

NG 5/16/A self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,6 A at 230 V / 2,7 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 4,5 m3/h
Maximum pump head according to the characteristic curve: 64 m
Characteristic curve Q/H: 0 m3/h → 64 m; 0,5 m3/h → 59 m; 1 m3/h → 54 m; 1,5 m3/h → 50 m; 2 m3/h → 46 m; 2,5 m3/h → 43 m; 3 m3/h → 40 m; 3,5 m3/h → 37 m; 4 m3/h → 34,5 m; 4,5 m3/h → 32 m3/h
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1
Dimensions: a 160 mm; a1 10 mm; b 40 mm; fM 560 mm; g1 11 mm; h1 165 mm; h2 57 mm; HD 240 mm; m1 60 mm; m3 10 mm; n1 215 mm; n2 175 mm; s 11.5 mm; w 115 mm
Article weight: 28,1 kg
Materials: pump housing, cover and diffuser plate GJL 200; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: A

SKU:: 70A00041200
Shipping weight:: 36.53 kg
Item weight:: 28.10 kg

831,02 € *

Available

Delivery time: ca. 3 weeks

NG 5/22/A self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,6 A at 230 V / 2,7 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 9,5 m3/h
Maximum pump head according to the characteristic curve: 36,5 m
Characteristic curve Q/H: 0 m3/h → 36,5 m; 0,5 m3/h → 35,5 m; 1 m3/h → 34,5 m; 1,5 m3/h → 33 m; 2 m3/h → 31,5 m; 2,5 m3/h → 30,5 m; 3 m3/h → 29,5 m; 3,5 m3/h → 28 m; 4 m3/h → 27 m; 4,5 m3/h → 26 m; 5 m3/h → 25 m; 5,5 m3/h → 23,5 m; 6 m3/h → 23 m; 6,5 m3/h → 21,5 m; 7 m3/h → 20,5 m; 8 m3/h → 18,5 m; 9 m3/h → 16,5 m; 9,5 m3/h → 15,5 m3/h
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1
Dimensions: a 160 mm; a1 10 mm; b 40 mm; fM 560 mm; g1 11 mm; h1 165 mm; h2 57 mm; HD 240 mm; m1 60 mm; m3 10 mm; n1 215 mm; n2 175 mm; s 11.5 mm; w 115 mm
Article weight: 28,1 kg
Materials: pump housing, cover and diffuser plate GJL 200; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: A

SKU:: 70A00043200
Shipping weight:: 36.53 kg
Item weight:: 28.10 kg

831,02 € *

Available

Delivery time: ca. 3 weeks

A 50-125B/A self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,1 kW / 1,5 HP
Rated current: 4,6 A at 230 V / 2,7 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 30 m3/h
Maximum pump head according to the characteristic curve: 16,5 m
Characteristic curve Q/H: 0 m3/h → 16,5 m; 6 m3/h → 15,5 m; 9 m3/h → 14,9 m; 12 m3/h → 14,2 m; 15 m3/h → 12,9 m; 18 m3/h → 11,6 m; 21 m3/h → 10 m; 24 m3/h → 8,3 m; 27 m3/h → 6,2 m; 30 m3/h → 4 m
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 2; Pressure side DN2 G 2
Dimensions: a 147 mm; b 50 mm; fM 490 mm; g1 12 mm; h1 231 mm; h2 64 mm; HD 223 mm; l1 96 mm; l2 102 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; n3 30 mm; s 16 mm; w 263 mm
Article weight: 28,3 kg
Materials: pump housing, suction housing and impeller GJL 200; shaft depending on the size AISI 303 or AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier
Revision: A

SKU:: 60F00862000
Shipping weight:: 36.79 kg
Item weight:: 28.30 kg

1.088,46 € *

Available

Delivery time: ca. 3 weeks

NG 6/18/A self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,5 kW / 2 HP
Rated current: 7,5 A at 230 V / 4,3 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: up to 6 m3/h
Maximum pump head according to the characteristic curve: 67,3 m
Characteristic curve Q/H: 0 m3/h → 67,3 m; 0,5 m3/h → 64,5 m; 1 m3/h → 62 m; 1,5 m3/h → 59 m; 2 m3/h → 56 m; 2,5 m3/h → 54 m; 3 m3/h → 51 m; 3,5 m3/h → 48,5 m; 4 m3/h → 46 m; 4,5 m3/h → 43,5 m; 5 m3/h → 41,5 m; 5,5 m3/h → 39 m; 6 m3/h → 36,5 m
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1
Dimensions: a 160 mm; a1 10 mm; b 40 mm; fM 560 mm; g1 11 mm; h1 165 mm; h2 57 mm; HD 240 mm; m1 60 mm; m3 10 mm; n1 215 mm; n2 175 mm; s 11.5 mm; w 115 mm
Article weight: 29,7 kg
Materials: pump housing, cover and diffuser plate GJL 200; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: A

SKU:: 70A00044200
Shipping weight:: 38.61 kg
Item weight:: 29.70 kg

939,95 € *

Available

Delivery time: ca. 3 weeks

NG 6/22/A self-priming jet pump with built-in ejector

Construction: Self-priming flat well jet pump in block construction with built-in ejector
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For well extraction, pressure increase, clean liquids or slightly contaminated surface water, garden watering and water jet cleaning
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,5 kW / 2 HP
Rated current: 7,5 A at 230 V / 4,3 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 9,5 m3/h
Maximum pump head according to the characteristic curve: 53 m
Characteristic curve Q/H: 0 m3/h → 53 m; 0,5 m3/h → 51,5 m; 1 m3/h → 50 m; 1,5 m3/h → 48,5 m; 2 m3/h → 47 m; 2,5 m3/h → 46 m; 3 m3/h → 44,5 m; 3,5 m3/h → 43 m; 4 m3/h → 41,5 m; 4,5 m3/h → 40 m; 5 m3/h → 39 m; 5,5 m3/h → 37,5 m; 6 m3/h → 36,5 m; 6,5 m3/h → 35 m; 7 m3/h → 33,5 m; 8 m3/h → 31 m; 9 m3/h → 28,5 m; 9,5 m3/h → 27 m3/h
Media temperature: to +40 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 10 bar
Connections according to ISO 228: suction side DN1 G 1 1/2; Pressure side DN2 G 1
Dimensions: a 160 mm; a1 10 mm; b 40 mm; fM 560 mm; g1 11 mm; h1 165 mm; h2 57 mm; HD 240 mm; m1 60 mm; m3 10 mm; n1 215 mm; n2 175 mm; s 11.5 mm; w 115 mm
Article weight: 29,7 kg
Materials: pump housing, cover and diffuser plate GJL 200; Brass impeller CW617N; Diffuser and nozzle Noryl PPO-GF20; shaft AISI 430F/AISI 303; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal
Revision: A

SKU:: 70A00045200
Shipping weight:: 38.61 kg
Item weight:: 29.70 kg

939,95 € *

Available

Delivery time: ca. 3 weeks

A 50-125A/A self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Cast iron version with pump housing and lantern from GJL 200
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 1,5 kW / 2 HP
Rated current: 7,5 A at 230 V / 4,3 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 33 m3/h
Maximum pump head according to the characteristic curve: 20,5 m
Characteristic curve Q/H: 0 m3/h → 20,5 m; 6 m3/h → 19,5 m; 9 m3/h → 19 m; 12 m3/h → 18 m; 15 m3/h → 17 m; 18 m3/h → 15,5 m; 21 m3/h → 14 m; 24 m3/h → 12,5 m; 27 m3/h → 10,5 m; 30 m3/h → 8 m; 33 m3/h → 5 m
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 2; Pressure side DN2 G 2
Dimensions: a 147 mm; b 50 mm; fM 490 mm; g1 12 mm; h1 231 mm; h2 64 mm; HD 223 mm; l1 96 mm; l2 102 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; n3 30 mm; s 16 mm; w 263 mm
Article weight: 29,8 kg
Materials: pump housing, suction housing and impeller GJL 200; shaft depending on the size AISI 303 or AISI 430F; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier
Revision: A

SKU:: 60F00902000
Shipping weight:: 38.74 kg
Item weight:: 29.80 kg

1.132,91 € *

Available

Delivery time: ca. 3 weeks

BA 50-125CE self-priming centrifugal pump with open impeller

Construction: Self-priming centrifugal pump of block construction with open impeller and integrated backflow preventer for automatic re-priming
Design: Bronze version with pump housing and bronze lantern CC480K
Applications: For clean or easily polluted water; solids up to 10 mm at A 40/A 50 and up to 15 mm at A 65/A 80; For drainage, irrigation and municipal and industrial applications
Engine: 2-poleer three-phase induction motor
Rated voltage: 230 V / 400 V ±10 %, 50 Hz
Engine rated power P2: 0,75 kW / 1 HP
Rated current: 4 A at 230 V / 2,3 A at 400 V
Rated speed: 2900 min-1
Efficiency class: IE3
Degree of protection: IP54
Insulation class: F
Operation mode: Continuous operation
Flow according to characteristic curve: to 27 m3/h
Maximum pump head according to the characteristic curve: 13,7 m
Characteristic curve Q/H: 0 m3/h → 13,7 m; 6 m3/h → 12,8 m; 9 m3/h → 12,2 m; 12 m3/h → 11,3 m; 15 m3/h → 10 m; 18 m3/h → 8,5 m; 21 m3/h → 7 m; 24 m3/h → 5,3 m; 27 m3/h → 3,3 m3/h
Media temperature: -10 to +90 °C
Maximum ambient temperature: to 40 °C
Maximum permissible working pressure: 6 bar; A 80-170 to 10 bar
Connections according to ISO 228: suction side DN1 G 2; Pressure side DN2 G 2
Dimensions: a 147 mm; b 50 mm; fM 490 mm; g1 12 mm; h1 231 mm; h2 64 mm; HD 223 mm; l1 96 mm; l2 102 mm; m1 100 mm; m2 70 mm; n1 190 mm; n2 140 mm; n3 30 mm; s 16 mm; w 263 mm
Article weight: 31,2 kg
Materials: pump housing, suction housing and impeller bronze CC480K; shaft AISI 316; Slip ring seal carbon/ceramic/NBR
Design according to: EN 60034-1; EN 60034-30-1; EN 60335-1; EN 60335-2-41
Options on request: other voltages; 60 Hz; IP55; Special sliding ring seal; higher or lower media or ambient temperatures; Embodiment with bearing carrier

SKU:: 61F00821000
Shipping weight:: 40.56 kg
Item weight:: 31.20 kg

2.436,61 € *

Available

Delivery time: ca. 3 weeks

Items 1 - 30 of 52