Skip to main content Skip to search Skip to navigation
Which pump suits your system?

Check flow rate and head together, using pump curves, pipe-loss calculations and clear explanations.

Start pump advisor →

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-001
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-002
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-003
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-004
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-005
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays
In stock

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-006
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 1 - 3 Workdays
In stock

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-007
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 1 - 3 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-008
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays
In stock

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-009
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 1 - 3 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-010
Shipping weight:
2.08 kg
Item weight:
1.60 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays
In stock

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-011
Shipping weight:
2.28 kg
Item weight:
1.80 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 1 - 3 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-012
Shipping weight:
2.28 kg
Item weight:
1.80 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-013
Shipping weight:
2.28 kg
Item weight:
1.80 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Three-phase AC version,
60 l/min at 1 m or 30 l/min at 4 m, 2800 rpm; IP54; insulation class F; S1 cos phi 0,70
120 W; 0,34–0,36A at 220–230V, 50Hz / 0,19–0,20A at 380–400V, 50Hz
120 W; 0,37–0,38A at 240–260V, 60Hz / 0,22–0,24A at 415–440V, 60Hz

Single-phase AC version
55 l/min at 1 m or 24 l/min at 4 m, 2750 rpm; IP54; insulation class F; S1
with installed operating capacitor 2.5 uF / 450V, 80 W; Rated current: 0,38A
incl. EC declaration of incorporation including installation, operating and maintenance instructions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V2A stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 1/2 inches as far as possible so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006895-014
Shipping weight:
2.28 kg
Item weight:
1.80 kg
415,31 € * 349,00 € excl. VAT
Available
Delivery time: 8 - 10 Workdays

Rated motor output P2: Three-phase model 150: 0.19 kW. The curve in the linked data sheet applies to this version; maximum head is approximately 10 m at shut-off. Available flow depends on the required head.

Single-phase model 150M: 0.17 kW. A separate, unambiguously assigned Q-H curve is not yet available for this version. Do not apply the three-phase flow/head figures unchanged; have the required duty point confirmed before selection.

Motor output P2 differs from electrical input P1. No dry running. Mount the motor above the liquid and observe the minimum liquid level and immersion length of the selected version.

Catalog and dimensions

The maximum flow rate as a function of the discharge head.
Note that the optional single-phase version delivers approximately 10% less output.

The housing is made of extruded aluminium or non-combustible, acid-resistant plastic according to the following standards: VDE 0730 and UL 94. The pump shaft is made of V-2A-stainless steel, the bearings are made of NSK, extremely durable and vibration-damped mounted in semi-rigid shells, which leads to an virtually vibration-free operation.

They are used for conveying cooling water, cooling emulsions, and low-viscosity drilling and cutting oils in all machining machine tools. They are known in industry as reliable pumps and have been used for years with good success. Coolant submersible pumps operate as centrifugal pumps, the stuffing boxes and the suction line being omitted by the pump part projecting into the liquid. They are largely insensitive to contaminated coolants.

When starting up, the direction of rotation must be observed (see arrow on the housing) The liquid level should remain a maximum of a few cm below the flange and minimally cover the pump. The pressure line to the workpiece should be 3/4 inches as far as possible, so that the values given in the table are achieved. Any smaller quantity can be set by means of a shut-off valve. Pressure relief valves are not required. The coolant submersible pumps are not intended for dry running.

SKU:
006896
Variations in:
  • Diving depth
  • Operating voltage
Shipping weight:
2.60 kg
Item weight:
2.00 kg
686,63 € - 810,39 € * from 577,00 € excl. VAT
Available

MXV 65-3202/D - Three-phase motor 4 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440221L00
Shipping weight:
93.60 kg
Item weight:
72.00 kg
3.481,71 € * 2.925,81 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3203/C - Three-phase motor 5.5 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440321B00
Shipping weight:
120.90 kg
Item weight:
93.00 kg
4.571,88 € * 3.841,92 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3204/C - Three-phase motor 7.5 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440421B00
Shipping weight:
130.91 kg
Item weight:
100.70 kg
5.137,16 € * 4.316,94 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3205/D - Three-phase motor 11 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440521L00
Shipping weight:
182.65 kg
Item weight:
140.50 kg
6.438,33 € * 5.410,36 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3206/D - Three-phase motor 11 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440621L00
Shipping weight:
187.20 kg
Item weight:
144.00 kg
7.086,12 € * 5.954,72 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3207/D - Three-phase motor 15 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440721L00
Shipping weight:
213.20 kg
Item weight:
164.00 kg
8.928,22 € * 7.502,71 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3208/D - Three-phase motor 15 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440821L00
Shipping weight:
214.50 kg
Item weight:
165.00 kg
9.343,48 € * 7.851,66 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3209/E - Three-phase motor 18.5 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50440921S00
Shipping weight:
250.51 kg
Item weight:
192.70 kg
10.136,73 € * 8.518,26 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3210/E - Three-phase motor 18.5 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50441021S00
Shipping weight:
253.11 kg
Item weight:
194.70 kg
10.868,89 € * 9.133,52 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 65-3212/D - Three-phase motor 22 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50441221L00
Shipping weight:
266.24 kg
Item weight:
204.80 kg
11.998,51 € * 10.082,78 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 80-4801/D - Three-phase motor 4 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50450121L00
Shipping weight:
95.29 kg
Item weight:
73.30 kg
3.622,10 € * 3.043,78 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 80-4802/C - Three-phase motor 5.5 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50450221B00
Shipping weight:
121.94 kg
Item weight:
93.80 kg
4.471,98 € * 3.757,97 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 80-4803/C - Three-phase motor 7.5 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50450321B00
Shipping weight:
134.16 kg
Item weight:
103.20 kg
5.260,36 € * 4.420,47 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 80-4804/D - Three-phase motor 11 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50450421L00
Shipping weight:
200.20 kg
Item weight:
154.00 kg
6.658,22 € * 5.595,14 € excl. VAT
Available
Delivery time: 2 - 4 Workdays

MXV 80-4805/D - Three-phase motor 15 kW - Round flange - AISI 304/GJL

Vertical multistage in-line pump for water supply, pressure boosting and irrigation. The opposing suction and delivery connections share a common axis.

SKU:
50450521L00
Shipping weight:
215.15 kg
Item weight:
165.50 kg
7.709,26 € * 6.478,37 € excl. VAT
Available
Delivery time: 2 - 4 Workdays