MP-DC motors
Protection class IP40 - Voltages between 12V and 170 Volt are available. Speed 3000 min-1
These permanent magnet DC motors are manufactured in four outer diameter sizes - ø48, ø65, ø80 and ø110 mm - with different lengths, covering power ranges up to 500 watts. Each of these sizes can be customised in terms of power supply, speed, connection configuration, options and more. A standard self-ventilation system can be supplied on request to achieve a power increase of approx. 30 %. Additional options are available for power ranges above 500 watts to allow an even higher level of customisation: The technical department is ready to solve any project at no additional cost in order to obtain the most suitable product for the customer's requirements.
MP42.96 — Permanent magnet DC motor
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 45 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 6 | A |
| Rated torque | On request | Nm |
| Maximum torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | On request | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 90 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 6 | A |
| Rated torque | 0.3 | Nm |
| Maximum torque | 1.2 | Nm |
| Duty type | S1 | |
| Maximum current | 24 | A |
| Armature resistance | 0.8 | Ω |
| Armature inductance | 1.6 | mH |
| Design and mechanics | ||
| Housing diameter | 65 | mm |
| Article weight | 2.35 | kg |
| IEC mounting size | 56 | |
| Mounting | B14A | |
| Flange outside diameter | 80 | mm |
| Bolt circle | 65 | mm |
| Pilot diameter | 50 | mm |
| Shaft Ø × length | 9 × 20 | mm |
| Shaft key | Yes | |
| Base motor rotor inertia | 0.0001 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | Without fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
| Holding brake | No | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.
MP42.50 — Permanent magnet DC motor
| Parameter | Value | Unit |
|---|---|---|
| Operating data | ||
| Rated voltage | 48 | V DC |
| Output power | 45 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 1.4 | A |
| Rated torque | 0.15 | Nm |
| Maximum torque | 0.6 | Nm |
| Duty type | S1 | |
| Maximum current | 5.5 | A |
| Armature resistance | 3.8 | Ω |
| Armature inductance | 12 | mH |
| Design and mechanics | ||
| Housing diameter | 65 | mm |
| Article weight | 1.5 | kg |
| IEC mounting size | 56 | |
| Mounting | B14A | |
| Flange outside diameter | 80 | mm |
| Bolt circle | 65 | mm |
| Pilot diameter | 50 | mm |
| Shaft Ø × length | 9 × 20 | mm |
| Shaft key | On request | |
| Base motor rotor inertia | 0.00005 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | Without fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
| Holding brake | No | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.