MP-DC motors
Protection class IP40 - Voltages between 12V and 170 Volt are available. Speed 3000 min-1
These permanent magnet DC motors are manufactured in four outer diameter sizes - ø48, ø65, ø80 and ø110 mm - with different lengths, covering power ranges up to 500 watts. Each of these sizes can be customised in terms of power supply, speed, connection configuration, options and more. A standard self-ventilation system can be supplied on request to achieve a power increase of approx. 30 %. Additional options are available for power ranges above 500 watts to allow an even higher level of customisation: The technical department is ready to solve any project at no additional cost in order to obtain the most suitable product for the customer's requirements.
MP55.15X — Permanent magnet DC motor
Series overview. The operating points and mechanics of the selected article variant apply.
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 130 | W |
| Speed | 1,700 | min⁻¹ |
| Rated current | 14 | A |
| Rated torque | 0.75 | Nm |
| Duty type | S1 | |
| Maximum current | 30 | A |
| Armature resistance | 0.4 | Ω |
| Armature inductance | 1 | mH |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 115 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 12.6 | A |
| Rated torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 50 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 3 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 230 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 12.6 | A |
| Rated torque | 0.75 | Nm |
| Duty type | S1 | |
| Maximum current | 50 | A |
| Armature resistance | 0.45 | Ω |
| Armature inductance | 2 | mH |
| Operating data · Operating point 4 (36 V DC) | ||
| Rated voltage | 36 | V DC |
| Output power | 230 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 8.4 | A |
| Rated torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 34 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 5 (48 V DC) | ||
| Rated voltage | 48 | V DC |
| Output power | 230 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 6.3 | A |
| Rated torque | 0.75 | Nm |
| Duty type | S1 | |
| Maximum current | 25 | A |
| Armature resistance | 1.1 | Ω |
| Armature inductance | 5 | mH |
| Operating data · Operating point 6 (170 V DC) | ||
| Rated voltage | 170 | V DC |
| Output power | 115 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 1.8 | A |
| Rated torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 7 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 7 (170 V DC) | ||
| Rated voltage | 170 | V DC |
| Output power | 230 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 1.8 | A |
| Rated torque | 0.75 | Nm |
| Duty type | S1 | |
| Maximum current | 7 | A |
| Armature resistance | 6 | Ω |
| Armature inductance | 40 | mH |
| Design and mechanics | ||
| Housing diameter | 80 | mm |
| Mounting | Depending on version | |
| Base motor rotor inertia | 0.00045 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | Without fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.
MP55.15V — Permanent magnet DC motor
Series overview. The operating points and mechanics of the selected article variant apply.
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 170 | W |
| Speed | 1,700 | min⁻¹ |
| Rated current | 18.3 | A |
| Rated torque | 0.98 | Nm |
| Maximum torque | 2 | Nm |
| Duty type | S1 | |
| Maximum current | 30 | A |
| Armature resistance | 0.4 | Ω |
| Armature inductance | 1 | mH |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 150 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 12.6 | A |
| Rated torque | On request | Nm |
| Maximum torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 50 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 3 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 300 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 16.4 | A |
| Rated torque | 0.98 | Nm |
| Maximum torque | 3 | Nm |
| Duty type | S1 | |
| Maximum current | 50 | A |
| Armature resistance | 0.45 | Ω |
| Armature inductance | 2 | mH |
| Operating data · Operating point 4 (36 V DC) | ||
| Rated voltage | 36 | V DC |
| Output power | 300 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Rated torque | On request | Nm |
| Maximum torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 34 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 5 (48 V DC) | ||
| Rated voltage | 48 | V DC |
| Output power | 300 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 8.2 | A |
| Rated torque | 0.98 | Nm |
| Maximum torque | 3 | Nm |
| Duty type | S1 | |
| Maximum current | 25 | A |
| Armature resistance | 1.1 | Ω |
| Armature inductance | 5 | mH |
| Operating data · Operating point 6 (170 V DC) | ||
| Rated voltage | 170 | V DC |
| Output power | 150 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 1.8 | A |
| Rated torque | On request | Nm |
| Maximum torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 7 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 7 (170 V DC) | ||
| Rated voltage | 170 | V DC |
| Output power | 300 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 2.3 | A |
| Rated torque | 0.98 | Nm |
| Maximum torque | 3 | Nm |
| Duty type | S1 | |
| Maximum current | 7 | A |
| Armature resistance | 6 | Ω |
| Armature inductance | 40 | mH |
| Design and mechanics | ||
| Housing diameter | 80 | mm |
| Mounting | Depending on version | |
| Base motor rotor inertia | 0.00045 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | With fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.
MP55.15V — Permanent magnet DC motor
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 130 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Duty type | S1 | |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 260 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Duty type | S1 | |
| Design and mechanics | ||
| Housing diameter | 80 | mm |
| Article weight | 5.6 | kg |
| IEC mounting size | 63 | |
| Mounting | B14A | |
| Flange outside diameter | 90 | mm |
| Bolt circle | 75 | mm |
| Pilot diameter | 60 | mm |
| Shaft key | On request | |
| Base motor rotor inertia | 0.00045 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | With fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
| Holding brake | On request | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.
MP55.10X — Permanent magnet DC motor
Series overview. The operating points and mechanics of the selected article variant apply.
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 120 | W |
| Speed | 2,300 | min⁻¹ |
| Rated current | 14 | A |
| Rated torque | 0.5 | Nm |
| Maximum torque | 1 | Nm |
| Duty type | S1 | |
| Maximum current | 28 | A |
| Armature resistance | 0.4 | Ω |
| Armature inductance | 1.3 | mH |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 75 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 4.3 | A |
| Rated torque | On request | Nm |
| Maximum torque | On request | Nm |
| Duty type | S1 | |
| Maximum current | 17 | A |
| Armature resistance | On request | Ω |
| Armature inductance | On request | mH |
| Operating data · Operating point 3 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 150 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 8.6 | A |
| Rated torque | 0.5 | Nm |
| Maximum torque | 2 | Nm |
| Duty type | S1 | |
| Maximum current | 34 | A |
| Armature resistance | 0.5 | Ω |
| Armature inductance | 3 | mH |
| Operating data · Operating point 4 (48 V DC) | ||
| Rated voltage | 48 | V DC |
| Output power | 150 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 4.3 | A |
| Rated torque | 0.5 | Nm |
| Maximum torque | 2 | Nm |
| Duty type | S1 | |
| Maximum current | 17 | A |
| Armature resistance | 1.3 | Ω |
| Armature inductance | 8 | mH |
| Design and mechanics | ||
| Housing diameter | 80 | mm |
| Mounting | Depending on version | |
| Base motor rotor inertia | 0.0003 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | Without fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.
MP55.10V — Permanent magnet DC motor
Series overview. The operating points and mechanics of the selected article variant apply.
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 100 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 11.5 | A |
| Duty type | S1 | |
| Maximum current | 45 | A |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 100 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 5.7 | A |
| Duty type | S1 | |
| Maximum current | 22.6 | A |
| Operating data · Operating point 3 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 200 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 11.5 | A |
| Duty type | S1 | |
| Maximum current | 45 | A |
| Operating data · Operating point 4 (48 V DC) | ||
| Rated voltage | 48 | V DC |
| Output power | 200 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | 5.7 | A |
| Duty type | S1 | |
| Maximum current | 22.6 | A |
| Design and mechanics | ||
| Housing diameter | 80 | mm |
| Mounting | Depending on version | |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | With fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.
MP55.05V — Permanent magnet DC motor
Series overview. The operating points and mechanics of the selected article variant apply.
| Parameter | Value | Unit |
|---|---|---|
| Operating data · Operating point 1 (12 V DC) | ||
| Rated voltage | 12 | V DC |
| Output power | 100 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Duty type | S1 | |
| Maximum current | 36 | A |
| Operating data · Operating point 2 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 50 | W |
| Speed | 1,500 | min⁻¹ |
| Rated current | 4.6 | A |
| Duty type | S1 | |
| Maximum current | 18 | A |
| Operating data · Operating point 3 (24 V DC) | ||
| Rated voltage | 24 | V DC |
| Output power | 100 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Duty type | S1 | |
| Maximum current | 18 | A |
| Operating data · Operating point 4 (36 V DC) | ||
| Rated voltage | 36 | V DC |
| Output power | 100 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Duty type | S1 | |
| Maximum current | 12 | A |
| Operating data · Operating point 5 (48 V DC) | ||
| Rated voltage | 48 | V DC |
| Output power | 100 | W |
| Speed | 3,000 | min⁻¹ |
| Rated current | On request | A |
| Duty type | S1 | |
| Maximum current | 9 | A |
| Design and mechanics | ||
| Housing diameter | 80 | mm |
| Mounting | Depending on version | |
| Base motor rotor inertia | 0.0002 | kg·m² |
| Equipment | ||
| Motor design | Permanent magnet DC motor | |
| Degree of protection | IP40 | |
| Insulation class | F | |
| Cooling | With fan | |
| Connection | Lead wires | |
| Bearings | Ball bearings | |
Series illustration; see data for configuration.
Unspecified values or values awaiting confirmation: on request. S6 duty and permissible overload: on request. Maximum current is not a permissible continuous current.