KG 050 worm gearbox max. 48...74 Nm; max. 0,12-0,75 kW

KG 050 worm gearbox max. 48...74 Nm; max. 0,12-0,75 kW

SKU: AR7348
Manufacturers: KEMMERICH ELEKTROMOTOREN

• Motor input IEC 063, 071, 080 / B14, B5
• max. 48...74 Nm; max. 0,12-0,75 kW
Hollow shaft Ø25x92 mm
• The output speeds are at an input speed of 1400 min^-1 Calculated
• Hole circle: 85 mm; Centering: 70 h8 mm; Peak height: 60 mm
• Foot hole spacing: 80 x 70 mm
• Including oil filling, Shell Omala S4 W E 320 / 0,15 liters
• Ambient temperature: -20°C to + 40°C
• Colouring: RAL 9022
• Housing: Aluminium
• The transmission (universal version U) can be mounted in any position

Speed reduction / output speed of the engine 1400 min-1
Engine input
Output flange (viewing direction relative to motor)
Output shaft
Protective cap hollow shaft

from

181,00 €

excl. 19% VAT , plus

Available
Delivery time: 4 - 6 Workdays (DE - int. shipments may differ)

pcs

Description
Downloads
PDF (1)

Warning: Check whether the maximum torque with the motor is not exceeded at full load:
Formula: Torque (Nm) = (power (kW) x eta (%) x 9550) / output speed (min)^-1)
eta (%) = efficiency of the transmission

The efficiency is crucial for the design of an application and is influenced by the gearing data. In the overview of the gearing data you will find values of the dynamic (n)₁=1400) and the static efficiency. It is noted that these table values are valid only after the entry time. In the case of a transmission with dynamic self-locking, the output shaft comes to a standstill immediately when the worm shaft is no longer driven. The theoretical prerequisite for dynamic self-locking is a dynamic efficiency ETA_{dd dd}<0,5. Bei statischer Selbsthemmung ist ein Anlauf aus dem Stillstand bei treibender Abtriebswelle nicht möglich. Statische Selbsthemmung liegt bei einem statischen Wirkungsgrad ETA_s<0,5 vor. In der Übersicht sind die Angaben zur Selbsthemmung nur als Richtwerte wiedergegeben. Die Bedingungen können durch Vibrationen oder Stöße beeinträchtigt werden. Bei der Prüfung der Selbsthemmung von Doppelschneckengetriebe ist zu beachten, dass sich der Gesamtwirkungsgrad aus dem Produkt der beiden einz elnen Wirkungsgrade ergibt, d.h. ETA_g = ETA₁ x ETA₂.

KG 40/50/63-Getriebe Optional with torque limiter available:
The torque limiter ensures the protection of the transmission against overloads.

Optional delivery
Twin-screw gearbox
Preliminary spur gear

BETRIEB UND EINFAHREN

In order to achieve the best performance, the transmission must be run-in during the first hours of operation by a gradual increase in power; In this phase, a temperature increase is considered normal.
In the event of malfunction, noise, oil leakage, etc. The transmission shall be immediately stopped and the cause removed as far as possible. Alternatively, you can send the part to our factory for control.

WARTUNG

The worm gearboxes from size 25 to size 90 and the precursor modules are lubricated with synthetic permanent oil and therefore do not require any maintenance.
The 110 and 130 size gearboxes are lubricated with mineral oil and are equipped with a vent plug. Therefore, the oil level must be checked regularly and, if necessary, replenished with the same oil or an oil compatible with the one indicated in our catalogue.
For 110 and 130 size gearboxes, the oil must be replaced after the first 300 hours of operation, with the correct quantity according to the installation position, as indicated in our catalogue, after the interior of the gearbox has been thoroughly cleaned.

Item information	Value
Shipping weight:	4.55 kg
Item weight:	3.50 kg

3D Downloads without/with motor (STEP, Solid Edge, IGES, ACIS, Parasolid)

3D downloads with pre-stage without/with motor

3D Downloads with twin-screw gearbox without/with motor